si vous avez été banni pour une raison de spam sur le forum (hacked account) c'est parce que votre compte a été utilisé par des Bots, merci d'envoyer un message via le formulaire de contact en bas de cette page afin de récupérer votre compte, les messages/discussions supprimés ne seront malheureusement pas restaurés.

Shadab · 31/10/2014, 20h30

Toyota Error Code: DTC P1300/14
Description: Igniter Circuit Malfunction

Probable causes:
1. Camshaft position sensor connector detached.
2. Camshaft position sensor failure.
3. Wiring.
4. ECM.

Do the following:
1. Check spark plug
2. Check for open and short in harness and connector in IGF signal circuit between
ECM and igniter
3. Disconnect igniter connector and check voltage between terminal IGF of ECM
connector and body ground.
4. Check for open and short in harness and connector in IGT1 – 3 signal circuit
between ECM and igniter
5. Check voltage between terminals IGT1 – 3 of ECM connector and body ground.
6. Disconnect igniter connector and check voltage between terminals IGT1 – 3 of
ECM connector and body ground.
8. Check for open and short in harness and connector between ignition switch and
ignition coil, ignition coil and igniter
9. Check ignition coil
10. Check and replace ECM

31/10/2014, 21h57

what is the question?

Shadab · 01/11/2014, 20h50

This is not the question but it is the solution how to repair the Toyota error code P1300.
Thanks.

31/10/2014, 20h30	#1
Shadab Débutant T-E Date d'inscription: septembre 2013 Localisation: Rawalpindi, Pakistan Messages: 29 Thanks: 28 Thanked 17 Times in 9 Posts Pouvoir de réputation: 0	Repairing Toyota error code P1300/13 Toyota Error Code: DTC P1300/14 Description: Igniter Circuit Malfunction Probable causes: 1. Camshaft position sensor connector detached. 2. Camshaft position sensor failure. 3. Wiring. 4. ECM. Do the following: 1. Check spark plug 2. Check for open and short in harness and connector in IGF signal circuit between ECM and igniter 3. Disconnect igniter connector and check voltage between terminal IGF of ECM connector and body ground. 4. Check for open and short in harness and connector in IGT1 – 3 signal circuit between ECM and igniter 5. Check voltage between terminals IGT1 – 3 of ECM connector and body ground. 6. Disconnect igniter connector and check voltage between terminals IGT1 – 3 of ECM connector and body ground. 8. Check for open and short in harness and connector between ignition switch and ignition coil, ignition coil and igniter 9. Check ignition coil 10. Check and replace ECM

Discussions similaires
Discussion	Auteur	Forum	Réponses	Dernier message
write error xprog m hc08 start error	alexisraynaud	Immobilizer dumps/solutions	5	12/08/2014 11h42
Error fatal : Unknown error during init	djkikou	Autocom, Delphi, Actia, Bosch, SPC, BrainBee, Autel	7	06/02/2014 09h07
Ford transit 2004 p1300	mohcin2	Mécanique générale	3	30/11/2013 05h55

31/10/2014, 21h57	#2
kitten13 Guest Messages: n/a	what is the question?

01/11/2014, 20h50	#3
Shadab Débutant T-E Date d'inscription: septembre 2013 Localisation: Rawalpindi, Pakistan Messages: 29 Thanks: 28 Thanked 17 Times in 9 Posts Pouvoir de réputation: 0	This is not the question but it is the solution how to repair the Toyota error code P1300. Thanks.