si vous avez été banni pour une raison de spam sur le forum (hacked account) c'est parce que votre compte a été utilisé par des Bots, merci d'envoyer un message via le formulaire de contact en bas de cette page afin de récupérer votre compte, les messages/discussions supprimés ne seront malheureusement pas restaurés.

runsun · 29/04/2014, 14h44

Hi !

I hope someone can answer me at these question:

Question : Is it possible to remove the EEPROM 95160 from at partly damaged BSI and solder/mount it in a new(used) BSI and resolve the immobilizer problem.

(After browsing the web I understands that all the immobilizer data are saved in the EEPROM 95160, - but maybe are the immobilizer data stored in several places in the BSI unit, I haven't found a proper solution) ?

Thanks for your interest !

Reg. Rune S. - Norway

**Amine-TE** · 29/04/2014, 16h52

On most of bsi it's possible, exept that one in 99% of case when you desolder the eprom ic it will be blank, need to recode with diag tool !

I got this many times.

Please don't forget to read rules and put an avatar and full location.

runsun · 30/04/2014, 07h26

Thanks Fondateur, may I should give it a try ?

Anything I can do to avoid erasing the eeprom, maybe proper wire to earth ?

Reg. Rune S. - Norway

**Amine-TE** · 30/04/2014, 18h50

You have to try, no warantee anyway.

runsun · 05/05/2014, 11h13

Hi !

Of note: I have changed eeprom95160 from a BSI(1) to another BSI(2) with the result that eeprom95160 data was deleted.
This work is NOT recommended....... :twisted:

re. Rune S. - Norway

avtec · 13/05/2014, 08h29

Citation:

Envoyé par runsun

Hi !

Of note: I have changed eeprom95160 from a BSI(1) to another BSI(2) with the result that eeprom95160 data was deleted.
This work is NOT recommended....... :twisted:

re. Rune S. - Norway

need an access code for immobilization and any device that can register keys. Code can be obtained from the engine or vin. BSI in the dump all in FF and encoding device, old keys are stored

johnnybeast · 31/07/2014, 02h58

Hi Runsun, the only way to get it back up and running now it to flash a 'virgin' BSI file to the 95160 EEPROM the re-configure with PP2000 or Lexia.

You will need the security code tho, you can get that from the ECU, which is stored on a small EEPROM in there. You'll need to read it and pop the file into ImmoTool or similar program and get the code from that.

valdir · 26/01/2016, 03h27

some cars run and some not, delete eeprom, really not a good way

29/04/2014, 14h44	#1
runsun Membre Non Confirmé Date d'inscription: avril 2014 Localisation: Skien Messages: 5 Thanks: 0 Thanked 0 Times in 0 Posts Pouvoir de réputation: 0	BSI - EEPROM 95160 replace/switch for C3, 2002, 1.4petrolKFV Hi ! I hope someone can answer me at these question: Question : Is it possible to remove the EEPROM 95160 from at partly damaged BSI and solder/mount it in a new(used) BSI and resolve the immobilizer problem. (After browsing the web I understands that all the immobilizer data are saved in the EEPROM 95160, - but maybe are the immobilizer data stored in several places in the BSI unit, I haven't found a proper solution) ? Thanks for your interest ! Reg. Rune S. - Norway

29/04/2014, 16h52	#2
Amine-TE Fondateur Date d'inscription: novembre 2008 Localisation: Offset: 0xFF25F255 Âge: 38 Messages: 120 930 Thanks: 2 741 Thanked 15 467 Times in 2 528 Posts Pouvoir de réputation: 1326	On most of bsi it's possible, exept that one in 99% of case when you desolder the eprom ic it will be blank, need to recode with diag tool ! I got this many times. Please don't forget to read rules and put an avatar and full location. __________________ Je ne donne pas d'aide en privé.

30/04/2014, 18h50	#4
Amine-TE Fondateur Date d'inscription: novembre 2008 Localisation: Offset: 0xFF25F255 Âge: 38 Messages: 120 930 Thanks: 2 741 Thanked 15 467 Times in 2 528 Posts Pouvoir de réputation: 1326	You have to try, no warantee anyway. __________________ Je ne donne pas d'aide en privé.

Discussions similaires
Discussion	Auteur	Forum	Réponses	Dernier message
cherche PINOUT BSI 206 eeprom 95160	beka1975	Flasheur de calculateur	1	06/12/2013 18h20
identification eeprom 95160 bsi	sofiane78	Réparation & Programmation des calculateurs	5	15/02/2013 07h47
delphi eeprom 95160	autodiagnos kamal	Immobilizer dumps/solutions	5	14/01/2013 09h56
clio 3 rs Eeprom 95160 S3000	powermap	Immobilizer dumps/solutions	7	18/12/2012 23h50
Seeprog et eeprom 95160	benaknoun	Programmeur de chip	3	09/06/2010 13h05

30/04/2014, 07h26	#3
runsun Membre Non Confirmé Date d'inscription: avril 2014 Localisation: Skien Messages: 5 Thanks: 0 Thanked 0 Times in 0 Posts Pouvoir de réputation: 0	Thanks Fondateur, may I should give it a try ? Anything I can do to avoid erasing the eeprom, maybe proper wire to earth ? Reg. Rune S. - Norway

05/05/2014, 11h13	#5
runsun Membre Non Confirmé Date d'inscription: avril 2014 Localisation: Skien Messages: 5 Thanks: 0 Thanked 0 Times in 0 Posts Pouvoir de réputation: 0	Hi ! Of note: I have changed eeprom95160 from a BSI(1) to another BSI(2) with the result that eeprom95160 data was deleted. This work is NOT recommended....... :twisted: re. Rune S. - Norway

31/07/2014, 02h58	#7
johnnybeast Membre Non Confirmé Date d'inscription: juillet 2014 Localisation: Dudley, UK Messages: 7 Thanks: 0 Thanked 0 Times in 0 Posts Pouvoir de réputation: 0	Hi Runsun, the only way to get it back up and running now it to flash a 'virgin' BSI file to the 95160 EEPROM the re-configure with PP2000 or Lexia. You will need the security code tho, you can get that from the ECU, which is stored on a small EEPROM in there. You'll need to read it and pop the file into ImmoTool or similar program and get the code from that.

26/01/2016, 03h27	#8
valdir Débutant Date d'inscription: novembre 2008 Localisation: Passo Fundo, RS Brasil Âge: 52 Messages: 10 Thanks: 13 Thanked 1 Time in 1 Post Pouvoir de réputation: 0	some cars run and some not, delete eeprom, really not a good way