si vous avez été banni pour une raison de spam sur le forum (hacked account) c'est parce que votre compte a été utilisé par des Bots, merci d'envoyer un message via le formulaire de contact en bas de cette page afin de récupérer votre compte, les messages/discussions supprimés ne seront malheureusement pas restaurés.

Kellertroll · 21/01/2014, 16h02

Hello guys,

i own a Peugeot 307 SW 1.6 Gasoline Year: 2005. I want to read out my faults so i bought a chinese Interface.

Here starts the problems.

My interface has:
Firmware 4.3.0
Serial 963830 B/ Peugeot

I tryed Diagbox 7.04 but i cannot communitcate with the car. So i start to read in the net about it. I found some people that say with a B/ in your Serial you maybe blacklisted in Diagbox Version later than 5.29 is this right?

Can someone help me with my problem and the interface or give me some tips what can i check or what should i do to get a connection to my car.

P.S. I came to the point where the Software ask for DAM Number. I use the Number from my Tyrepressure Sticker on my driver door. I hope that is the right number. But i got alyways the message cannot communicate with the chip.

greetings Troll

**devildante007** · 21/01/2014, 16h29

Hi guy,

Your interface must be flash and after you go to work with diagbox 7.XX.
Two ways to flash your interface:
by software: contact nlc (member) by pm
by hardware: flash SPI and MCU MB90F546GS with universal and ISP prog!

Regards.

Kellertroll · 21/01/2014, 16h34

Ok thats a point to think about.

Can i get Diagbox 5.29 anywere?
I want to try if the interface work or not.

I try to write nlc a pm and ask him for help...when i find the user nlc

**devildante007** · 21/01/2014, 16h36

Citation:

Envoyé par Kellertroll

Can i get Diagbox 5.29 anywere?
I want to try if the interface work or not.

With lexia3 V45 or PP2000 it's better for try interface for me !

Regards.

Kellertroll · 21/01/2014, 17h06

So you think i should give PP2000 a try?
Without DiagBox?

**devildante007** · 21/01/2014, 19h18

yes, without diagbox on CAN VAN and full CAN vehicles !

Regards

sylvain02120 · 21/01/2014, 19h22

Certaines interfaces xs evolution chinoises ne fonctionnent pas sur les 307 ou C5, ton interface est peut etre de mauvaise qualité

Kellertroll · 21/01/2014, 21h23

Right now i tryed Diagbox 5.29 before i try PP2000 i cannot connect to my car.

Kellertroll · 21/01/2014, 21h56

Which version of PP2000 or lexia should i use to try.
I my softwarebox there would be no point that say CAN and VAN communication.

**mod-files.com** · 21/01/2014, 22h34

Citation:

Envoyé par Kellertroll

Which version of PP2000 or lexia should i use to try.
I my softwarebox there would be no point that say CAN and VAN communication.

dont try any more if it doesnt work with pp2000 , forget it and you have to take an other one

Kellertroll · 22/01/2014, 11h42

Yes this is the only way send this back to the seller.

**devildante007** · 22/01/2014, 12h26

Good decision !

And see you soon, for a return of your diag with new interface....

@++

21/01/2014, 16h02	#1
Kellertroll Débutant Date d'inscription: janvier 2014 Localisation: Germany Messages: 13 Thanks: 0 Thanked 1 Time in 1 Post Pouvoir de réputation: 0	DiagBox 7.04 Peugeot 307 Interface Problems Hello guys, i own a Peugeot 307 SW 1.6 Gasoline Year: 2005. I want to read out my faults so i bought a chinese Interface. Here starts the problems. My interface has: Firmware 4.3.0 Serial 963830 B/ Peugeot I tryed Diagbox 7.04 but i cannot communitcate with the car. So i start to read in the net about it. I found some people that say with a B/ in your Serial you maybe blacklisted in Diagbox Version later than 5.29 is this right? Can someone help me with my problem and the interface or give me some tips what can i check or what should i do to get a connection to my car. P.S. I came to the point where the Software ask for DAM Number. I use the Number from my Tyrepressure Sticker on my driver door. I hope that is the right number. But i got alyways the message cannot communicate with the chip. greetings Troll

Discussions similaires
Discussion	Auteur	Forum	Réponses	Dernier message
quelle est la version diagbox que je l'installer pour mon interface!!	PIC16F84	LEXIA, PP2000, DiagBox	3	14/04/2015 22h01
conseil interface diagbox	foulques	LEXIA, PP2000, DiagBox	7	25/08/2013 17h07
interface clone PSA non reconnue par Diagbox	ramses74	LEXIA, PP2000, DiagBox	22	31/01/2012 13h20
solution pour DIagbox avec interface clonée?????	adiago	Peugeot, Citroën	21	29/10/2011 13h06

21/01/2014, 16h29	#2
devildante007 V.I.P Date d'inscription: juin 2011 Localisation: France Messages: 308 Thanks: 740 Thanked 868 Times in 192 Posts Pouvoir de réputation: 27	Hi guy, Your interface must be flash and after you go to work with diagbox 7.XX. Two ways to flash your interface: by software: contact nlc (member) by pm by hardware: flash SPI and MCU MB90F546GS with universal and ISP prog! Regards.

21/01/2014, 16h34	#3
Kellertroll Débutant Date d'inscription: janvier 2014 Localisation: Germany Messages: 13 Thanks: 0 Thanked 1 Time in 1 Post Pouvoir de réputation: 0	Ok thats a point to think about. Can i get Diagbox 5.29 anywere? I want to try if the interface work or not. I try to write nlc a pm and ask him for help...when i find the user nlc

21/01/2014, 17h06	#5
Kellertroll Débutant Date d'inscription: janvier 2014 Localisation: Germany Messages: 13 Thanks: 0 Thanked 1 Time in 1 Post Pouvoir de réputation: 0	So you think i should give PP2000 a try? Without DiagBox?

21/01/2014, 19h18	#6
devildante007 V.I.P Date d'inscription: juin 2011 Localisation: France Messages: 308 Thanks: 740 Thanked 868 Times in 192 Posts Pouvoir de réputation: 27	yes, without diagbox on CAN VAN and full CAN vehicles ! Regards

21/01/2014, 19h22	#7
sylvain02120 Membre trés attaché Date d'inscription: janvier 2013 Localisation: France,02260 Messages: 919 Thanks: 201 Thanked 750 Times in 429 Posts Pouvoir de réputation: 24	Certaines interfaces xs evolution chinoises ne fonctionnent pas sur les 307 ou C5, ton interface est peut etre de mauvaise qualité

21/01/2014, 21h23	#8
Kellertroll Débutant Date d'inscription: janvier 2014 Localisation: Germany Messages: 13 Thanks: 0 Thanked 1 Time in 1 Post Pouvoir de réputation: 0	Right now i tryed Diagbox 5.29 before i try PP2000 i cannot connect to my car.

21/01/2014, 21h56	#9
Kellertroll Débutant Date d'inscription: janvier 2014 Localisation: Germany Messages: 13 Thanks: 0 Thanked 1 Time in 1 Post Pouvoir de réputation: 0	Which version of PP2000 or lexia should i use to try. I my softwarebox there would be no point that say CAN and VAN communication.

22/01/2014, 11h42	#11
Kellertroll Débutant Date d'inscription: janvier 2014 Localisation: Germany Messages: 13 Thanks: 0 Thanked 1 Time in 1 Post Pouvoir de réputation: 0	Yes this is the only way send this back to the seller.

22/01/2014, 12h26	#12
devildante007 V.I.P Date d'inscription: juin 2011 Localisation: France Messages: 308 Thanks: 740 Thanked 868 Times in 192 Posts Pouvoir de réputation: 27	Good decision ! And see you soon, for a return of your diag with new interface.... @++